PD-Rapid-Stabilizer + Screw Kit 2.5 TDI
PD-Rapid-Stabilizer + Screw Kit 2.5 TDI
With 5 repair brackets - it couldn't be simpler: leave the injectors in, replace the bracket - permanently sealed. Installed in under 1 hour.
Install, start & have peace of mind 
Customers drive several hundred thousand km more with PDE repair holders 
Against starting problems, oil proliferation & vibrations 
180-day seal-or-money-back guarantee Nur 2,00 € je 1.000 km (bei 200.000 km)
Motor auswählen:
5-Zylinder
5-Zylinder Variante auswählen:
PDE-Reparaturhalter
5-Zylinder Set:
Schnellwechsel-Set
● In stock - With you in 1-3 working days
Couldn't load pickup availability
2.5 TDI engine code letters (affected engines)
2.5 TDI engine code letters (affected engines)
AXD, AXE, AYH, BPC, BNZ, BLJ, BAC, BLK, BLE, BPE, BPD, BBE, BBF
It is possible that your vehicle is also affected and we have not yet listed the code. Please let us know via the contact form - we will check your engine code immediately and add it to the list. This will also help other PDE drivers 🍀
Why should you act as quickly as possible?
Why should you act as quickly as possible?
Loose PDEs cause massive unnoticed damage to the cylinder head. The longer you wait, the deeper the PDE eats into the seat - and the more expensive the repair becomes.
Our PD-Rapid-Stabilizer stops the problem immediately, stabilizes the PDEs permanently and prevents further damage. Act now & save the engine!
For excessively damaged motors
For excessively damaged motors
Even severely damaged engines can still be saved. Install our reinforced sealing rings. These are slightly thicker and ensure a reinforced seal.
Installation
Installation
- Remove the expansion screws and the clamping shoe and disconnect the electrical plug.
- Place the PD-Rapid-Stabilizer directly on the PDE and tighten it with new expansion bolts .
- The alignment is done automatically and the engine is ready for use again, without any oil build-up or starting problems.
Instructions for use
Instructions for use
- Expansion bolts should be replaced as this is a special material which changes when tightened.
- Tighten with the appropriate torque
Of course, you can also pull out the PDEs, clean them and replace them with new wear parts
.
This PD-Rapid-Stabilizer was developed and tested in cooperation with a master car mechanic. You not only save time and money, but also reduce the risk of damage to the PDE during repair.
Note:
For engines with greater wear or problems in the injector area, we recommend the use of our reinforced sealing rings, which you can also find in our store.
Disclaimer:
At no time can we guarantee an improvement. Rather, we assure you that our product will bring about an improvement in most cases. It is at your discretion to use our product. We completely exclude consequential damages of any kind.
Scope of delivery
Scope of delivery
5x PD-Rapid-Stabilizer
5x expansion screw for PDE repair holder attachment
Shipping information (shipping with DHL)
Shipping information (shipping with DHL)
Delivery time: available immediately after receipt of payment.
We calculate the shipping costs for this product at 8.90€ per order.
PD-Injector-Stabilizer or PD-Rapid-Stabilizer - the most important differences at a glance
Both solutions reliably seal your PDEs - but with different effort, structure and objectives. Here you can see which solution is better suited to your situation.
PD-Injektor-Stabilizer - maximum stability for your engine
The PDE-Injector-Stabilizer replaces the original mounting on one side. This distributes the contact pressure evenly across all PDEs. No more vibrations, no more diesel in the oil - even if the seats are worn and damaged.
Advantages:
-
Most stable mounting on the market
-
Holds the PDEs in place, even if a thread is torn out during removal
-
Even pressure on all PDEs
-
Perfect for heavily worn cylinder heads
PD-Rapid-Stabilizer - clever, simple, effective
The PD-Rapid-Stabilizer also replaces the original one-sided fastening - but it fixes each PDE individually (e.g. 5 Rapid-Stabilizer for 5 cylinders). Thanks to its protected shape, it is so precisely adapted to the engine that vibrations are no longer possible. It provides a strong hold even with worn seats.
Advantages:
-
Fastest repair option without PDE removal
-
Ideal for DIY - remove the valve cover, replace the holder, done
-
You can seal each PDE individually
-
Saves expensive workshop time & costs for add-on parts
💡Tip:
Many customers first test the Rapid-Stabilizer without removing the PDE - in 95% of cases this is enough. If not, you can always reseal the PDEs later and fix them better.
Which repair option is right for me?
(ⓘ Scroll to the left on your cell phone to see the table in full)
| You want: | PDE-Injector-Stabilizer | PDE-Rapid-Stabilizer |
| Permanent tightness without vibration | ✅ | ✅ |
| Reseal all PDEs | ✅ | ✅ |
| Preventively protect the engine & avoid expensive consequential damage | ✅ | ✅ |
| Repair without dismantling the cylinder head | ✅ | |
| Inexpensive & quick repair yourself | ✅ | |
| Rescue a badly damaged cylinder head | ✅ | ✅ |
| Replace / seal each PDE individually | ✅ | |
| Test it without risk for 180 days | ✅ | ✅ |
| Have the strongest fixation | ✅ |
Which PD-Rapid-Stabilizer set suits your situation?
Here you can see at a glance what you need - and when which set makes sense for you.
Quick-change set
The simplest and quickest solution - ideal if you don't want to remove everything.
- No need to remove the PDEs
- Injector screws included
- Installation possible in under an hour
Tip:
Many customers install the repair bracket first without removing the PDEs. In over 90 % of cases, this already solves the problem. If not, you can always reorder the add-on parts & wiring harness later.
Installation kit (bestseller)
If you want to reseal the PDEs - but don't need to replace the wiring harness.
You don't need to worry about the right installation parts - everything is included:
- Contains everything from the quick-change set
- Includes all gasket sets + reinforced gaskets (for badly damaged injector seats)
- Includes expansion bolts for the rocker arm shaft
- Cheaper than buying everything separately - and you have everything right at hand
Important:
Special expansion bolts are loosened when removing the PDEs. These may only be used once. All seals must also be replaced - otherwise you risk leaks after installation.
Complete set (best value for money)
The perfect solution for anyone who doesn't want to make any mistakes and wants to be sure: Now I've done everything right.
- Contains everything from the installation set
- In addition: new tested PDE wiring harness - a frequent source of errors
- Saves double the work: If you have everything open anyway, replace the wiring harness at the same time. In this way, you rule out later sources of error and save yourself a second repair in case of doubt.
- You save the most money with the complete set because we can make you a better offer here than if you were to buy everything separately.
Why replace the wiring harness as well?
The PDE wiring harness is a frequent source of faults - especially in older vehicles.
Over time, heat and vibration cause cable breaks or contact problems that you don't see immediately. If you have everything open anyway, it makes perfect sense to replace it as a preventive measure.
💡Our tip:
If you are opening the engine anyway, the complete set is the worry-free choice.
You get everything in one package - perfectly coordinated.
If you realize that the quick-change set wasn't enough, the complete set is cheaper than ordering everything separately.
No need to buy more. No improvising. High-quality components, no cheap garbage.
-
Installed thousands of times & tried and tested over many years
-
Fastest PDE repair option on the market
-
Simple installation for do-it-yourselfers
-
Noticeably smoother running of the engine
The PD-Injector-Stabilizer alternative for 5-cylinder engines, the PD-Rapid-Stabilizer!
The fastest and easiest repair option ever! Customers report installation times of less than 1 hour. Since no removal of the rocker shaft or PDE injectors is necessary, the entire system remains assembled. The wearing parts do not need to be replaced.
Sets in comparison:
PD-Rapid-Stabilizer + Screw Kit
PD-Rapid-Stabilizer + Screw Kit 2.5 TDI
Secure now
Before - After
❌ Original holder
✅ PDE PD-Rapid-Stabilizer
Have you ever been disappointed? This time without risk.
Many customers come to us after other solutions have failed to hold.
We know how expensive and frustrating this can be - and we are absolutely certain that our PD-Injector-Stabilizer and the PD-Rapid-Stabilizer will solve the problem permanently.
That's why we give you the 180-day leak guarantee: if it doesn't work permanently - you get your money back. No ifs, ands or buts.
If you have already tried another solution that didn't work, contact us at.
We have permanently improved prices for just such cases.
Why workshops rely on us
